Made and counted by Wren —

Arrow stitch beanie pattern with a flat crochet crown

5mm hook and worsted weight yarn make this arrow stitch beanie with a flat, increase-built crown.

Arrow stitch beanie pattern with a flat crochet crown
IntermediateLevel
4-6 hoursTime
5 mmHook
WorstedYarn
Jump to the pattern

About this pattern

A top-down beanie worked in worsted weight yarn with a 5mm hook, starting as a flat circle increased from 10 to 70 double crochet stitches, then shaped into the body with single crochet rounds and an arrow stitch pattern made from front post triple crochets worked two rounds below. The 70-stitch round should measure about 6.5 inches (17 cm) across for adult sizing. Finished with a single crochet edge, fastened off, and ends woven in.

The pattern

Written out round by round

Materials

  • Worsted weight yarn
  • 5mm crochet hook

Abbreviations

  • sc = single crochet
  • dc = double crochet

Main Pattern

Round 1Start with a slip knot, chain 4, join with a slip stitch to form a ring. Chain 2 (does not count as a stitch), make 10 double crochets (DC) into the ring. Join with a slip stitch to the first DC.
Round 2Chain 2 (not a stitch), make 2 DC in each stitch around. Skip the initial 2 chains and join with a slip stitch to the first DC. You’ll have 20 DC.
Round 3Chain 2, make 2 DC into the first stitch, then 1 DC in the next stitch. Repeat the sequence around, ending with 30 DC in total. Join with a slip stitch.
Round 4Chain 2, 2 DC in the first stitch, then 1 DC in each of the next two stitches. Repeat around to have 40 DC. Join with a slip stitch.
Round 5Chain 2, 2 DC in the first stitch, then 1 DC in each of the next three stitches. Repeat around, ending with 50 DC. Join with a slip stitch.
Round 6Chain 2, 2 DC in the first stitch, then 1 DC in each of the next four stitches. Repeat around for a total of 60 DC. Join with a slip stitch.
Round 7Chain 2,2 DC in the first stitch, then 1 DC in each of the next five stitches. Repeat around for 70 DC in total. Check the diameter – it should be approximately 6.5 inches or 17 cm for an adult size. Join with a slip stitch.
Rounds 8–9Chain 2, 1 DC in each stitch around, no increases. Join with a slip stitch at the end of each round.
Round 10Turn work, chain 1, 1 single crochet (SC) into each stitch around. Join with a slip stitch.
Round 11Arrow Stitch Pattern Chain 2, turn work. Start making arrow stitches: Skip the slip stitch, work a starter of a DC, but don't complete.Yarn over twice, make a front post triple crochet around the third DC from two rounds below, but don't complete. Yarn over, pull through all loops on the hook. Make 3 DC behind this stitch, then a front post triple crochet, yarn over, and pull through all loops on the hook to complete the Arrow Stitch. Continue the sequence of 5 stitches to form the Arrow Stitch pattern around. Join with a slip stitch.
Round 12Turn work, chain 1, 1 SC into each stitch around. Join with a slip stitch.Repeat Rounds 11 and 12: Continue the pattern for the desired height of the hat.

Assembly

Step 1After completing the desired number of Arrow Stitch pattern repeats, finish by working a round of SC for a clean edge. Fasten off and weave in ends.
Step 2Once you've reached the desired height, work the last round in single crochet on the wrong side to create a neat edge. Join with a slip stitch, cut the yarn, leaving a tail, and pull it through to fasten. Weave in any loose ends.

Tester's notes

5mm hook holds the DC rounds loose enough to keep the crown flat; swap down to 4.5mm if round 7 measures larger than 6.5 inches.

Mark the first stitch of every increase round (rounds 2-7) with a stitch marker — the chain-2 doesn't count as a stitch, so miscounting the join point shifts the whole crown off-center.

The 2 SC rounds after the DC crown are worked with a turn, not continuous rounds — turn the work before each chain-1, or the arrow stitch rounds that follow will twist.

Front post triple crochets reach two rounds below the working row, so keep tension even on those two rounds or the arrows pucker instead of sitting flat.

One color, one yarn weight throughout this pattern — no color changes to plan for, so weave in ends only at the slip knot start and the final fasten-off.

Work in progress

Arrow stitch beanie pattern with a flat crochet crown — photo 2
Arrow stitch beanie pattern with a flat crochet crown — photo 3
Arrow stitch beanie pattern with a flat crochet crown — photo 4

At a glance

Rounds11
LevelIntermediate
Time4-6 hours
Hook5 mm
YarnWorsted

Gauge check

After round 7 (70 DC), lay the circle flat and measure straight across: it should read close to 6.5 inches (17 cm) for an adult head.

If something looks wrong

The crown cups instead of lying flat after round 7.
Increases are off — recount: round 7 should hold exactly 70 DC. Rip back to the last correct round and recount the increase sequence (2 DC in the marked stitch, then the stated number of single DC) before continuing.
Arrow stitches don't sit raised, they
Front post triple crochet was worked too loosely or around the wrong stitch two rounds below. Pull the working loop snug after the yarn-over-twice step, and count rounds down carefully before placing the post stitch.
The join at the end of a round leaves a visible step.
Slip stitch join was worked into the wrong loop or pulled too tight. Join into the first DC's top two loops only, and keep the slip stitch at the same tension as the surrounding DC.
70-stitch round measures more or less
Hook size or tension is off for this yarn. Measure again after blocking; if still off, redo the crown with a half-size hook change up or down and recheck at round 7.

Yarn substitutions

Acrylic, worsted weightClosest match to the pattern as written — same 5mm hook, same drape, holds the arrow stitch texture crisply.
Cotton blend, worsted weightLess stretch than the original fiber, so the 6.5 inch (17 cm) crown measurement runs tighter on the head; size up to a 5.5mm hook to compensate.
Wool or wool blend, worsted weightBlocks flatter and holds the front post triple crochet ridges better than acrylic; expect slight shrinkage, so check the round 7 diameter after a test swatch is washed.
FAQs

Questions

Why does round 2 need stitches skipped before joining?

The initial chain-2 at the start of each round doesn't count as a stitch, so joining into it instead of the first DC would add a phantom stitch and throw off the count. Skipping it keeps every round's total accurate for the next increase sequence.

How many rounds of single crochet come after the DC crown?

Two turned single crochet rounds follow the plain DC round, each started with chain 1 and worked by turning the piece. These set up the base before the arrow stitch pattern begins.

One at a time —

Get the next pattern

Tested round by round before it is sent. No spam.